EnGenius EAP9550 Manuale Utente

EnGenius EAP9550 11N Multi-Function AP/Repeater

4.1.4. Schedule  4.1.5. Event Log 4.1.6. Monitor The device will record the router transmission status in a time span.

 Detail: Click into detail to see historical record.

4.2. Wireless 4.2.1. AP 4.2.1.1. Status

4.2.1.2. Basic  Radio: To enable/disable wireless signal. • Mode: Define AP in different modes. When in AP mode, the device works as regular AP,

• MAC Address 1~4: To specify MAC address of other AP devices. MAC address will only shows when configured in WDS AP mode. • Security: Please ref

• Data rate: You may select a data rate from the drop-down list, however, it is recommended to select auto. This is also known as auto-fallback. •

 Encryption: WEP • ESSID Selection: As this device supports multiple SSIDs, it is possible to configure a different security mode for each SSID

packets are transmitted without encryption. Shared Key sends an unencrypted challenge text string to any device attempting to communicate with the AP.

• Broadcast SSID: Select Enable or Disable from the drop-down list. This is the SSID broadcast feature. When this option is set to Enabl

• ESSID Selection: As this device supports multiple SSIDs, it is possible to configure a different security mode for each SSID (profile). Select an

Table of Content 1. Introduction...4 1

4.2.1.6. WPS • WPS: Place a check in this box to enable this feature. • WPS Current Status: Displays the current status of the WPS configuration. •

4.2.1.8. VLAN Only Available in AP mode • Virtual LAN: Choose to Enable or Disable the VLAN features. • SSID1 Tag: Specify the VLAN tag.

4.2.1.9. WMM 4.2.2. WDS Bridge You can only connect to the device via Ethernet Port

4.2.2.1. Status 4.2.2.2. Basic • Radio: To enable/disable radio frequency. • Mode: WDS mode allows you to interlink with other AP devices. Setti

 2.4 GHz (N)  2.4 GHz (B+G)  2.4 GHz (G)  2.4 GHz (B+G+N) • Channel: You can manually configure a channel to be used. • MAC Address 1~4: T

alphanumeric characters) format. ASCII format is provided so you can enter a string that is easier to remember. • Default Tx Key: You may choose one

4.2.2.3. Advanced • Fragment Threshold: Packets over the specified size will be fragmented in order to improve performance on noisy

4.2.2.4. WMM

4.2.3. Universal Repeater (AP) 4.2.3.1. Status

4.2.3.2. Basic • Radio: To enable/disable radio frequency. • Mode: Universal Repeater • Band: Configure the device into different wireless modes

4.6. Logout...44 Appendix A – FCC Interfere

• Enabled SSID#: The device allows you to have 1 unique SSID • ESSID#: Description of each configured SSID • Site Survey: List out all connected de

• Preamble Type: Select a short or long preamble. For optimum performance it is recommended to also configure the client device as the sa

• ESSID Selection: As this device supports multiple SSIDs, it is possible to configure a different security mode for each SSID (profile). Select an

• Key Length: Select a 64-bit or 128-bit WEP key length from the drop-down list. • Key Type: Select a key type from the drop-down list. 128-bit en

connect to your network. When this is disabled, you must enter the Wireless Network Name (SSID) on the client manually to connect to the network. • W

4.2.3.6. WPS • WPS: Place a check in this box to enable this feature. • WPS Current Status: Displays the current status of the WPS configuration. •

4.2.3.8. WMM

4.3. Network 4.3.1. Status 4.3.2. LAN • Bridge Type: Select Static IP or Dynamic IP from the drop-down list. If you select Static IP, you will be r

Dynamic Host Configuration Protocol (DHCP) is a network application protocol used by devices (DHCP clients) to obtain configuration information for o

4.4. Management 4.4.1. Admin Change current login password of the device. It is recommended to change the default password for security reasons. 4

1. Introduction EAP9550 is a powerful and multi-functioned 11n Access Point and it can act three modes AP/WDS/Universal Repeater. Smoke detector a

• SNMP Active: Choose to enable or disable the SNMP feature. • SNMP Version: You may select a specific version or select All from the drop-down lis

4.4.4. Firmware It allows you to upgrade the firmware of the device in order to improve the functionality and performance.  Ensure that you have

4.5. Tools 4.5.1. Time Setting This feature allows you to configure, update, and maintain the correct time on the device’s internal system clock as

4.5.2. Power Saving 4.5.3. Diagnosis Check whether a network destination is reachable with ping service.

4.5.4. LED Control 4.6. Logout

Appendix A – FCC Interference Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply wi

Appendix B – IC Interference Statement Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operati

SNMP Remote Configuration Management Helping administrators to remotely configure or manage the Access Point easily QoS (WMM) support Enhancing user

2. Understanding the Hardware 2.1. Hardware Installation 1 Place the unit in an appropriate place after conducting a site survey. 2 Plug one end

3. Modes AP/WDS/Universal Repeater 3.1. Access Point In AP (Access Point) mode, your device acts as a communication hub for users with a wireless devi

4. Web Configuration 4.1. System 4.1.1. Operation Mode You are allowed to configure EAP9550 into different modes: AP, WDS Bridge and Universal Repeate

• System: Basic information of the device. • WLAN Settings: WLAN channel. • SSID_1: SSID information. 4.1.3. DHCP